Selecting an Ergo-Arm

Guide to Selecting the Best Ergo-Arm for Your Application

All Classic Ergo-Arms rotate on mounting post 180^o and allow a reach of 4 - 30 inches through the incorporation of a two piece articulating arm.  Ergo-Arms provide ergonomic support for electric and pneumatic tools, reduces operator fatigue and increases productivity, consistency, and accuracy.

• Reduce operator fatigue and increase productivity

• Use with inline pneumatic tool

• Vertical screw application

• Arm movement is up-down and 180^o side-side

• Dial regulator provides easy adjustment of counterbalance

• Power source for arm is pneumatic (air line is required)

• Reduce operator fatigue and increase productivity

• Use with inline electric tool; includes EAP-202ASSY driver tool mount

• Vertical screw application

• Arm movement is up-down and 180^o side-side

• Dial regulator provides easy adjustment of counterbalance

• Power source for arm is pneumatic (air line is required)

• Reduce operator fatigue and increase productivity

• Use with inline pneumatic tool

• Vertical screw application

• Arm movement is up-down and 180^o side-side

• Power source for arm is hydraulic (no air line is required)

• Single arm design allows operator control while absorbing torque reaction and supporting tool weight

• End of arm swivel tooling allows for maximum rotation of tool.  For use with:
  -Inline pneumatic tool is standard
  -Pistol grip or angle head pneumatic tool requires addition of part EAA-21
  -Inline electric tool requires addition of part EAP-202ED-KIT
  -Pistol grip electric tool requires addition of part EAA-21
  -Can be customized for use with Automatic Screwfeeder

• Horizontal, vertical or varied screw application

• Arm movement is forward-backward, up-down and 180^o side-side

• Dial regulator provides easy adjustment of counterbalance

• Power source for arm is pneumatic (air line is required)

• Single arm design allows operator control while absorbing torque reaction and supporting tool weight

• End of arm swivel tooling allows for maximum rotation of tool.  For use with:
  -Inline pneumatic tool is standard
  -Pistol grip or angle head pneumatic tool requires addition of part EAA-21
  -Inline electric tool requires addition of part EAP-202ED-KIT
  -Pistol grip electric tool requires addition of part EAA-21
  -Can be customized for use with Automatic Screwfeeder

• Horizontal, vertical or varied screw application

• Arm movement is forward-backward, up-down and 180^o side-side

• Dial regulator provides easy adjustment of counterbalance

• Power source for arm is hydraulic (no air line is required)

• Use with inline electric tool

• Vertical screw application

• Arm movement is up-down and 360^o side-side rotation unless limited by tool configuration.  Clearance required for movement equals reach of arm.*

• Smaller height and reach

• End of arm fixturing allows operator the full grip of tool with no pinch points

• Power source for arm is mechanical (no air line is required)

• Shipped with two ASB-0C balancers

• Use with inline electric tool or inline lower torque DC nutrunner

• Vertical screw application

• Arm movement is up-down and 360^o side-side rotation unless limited by tool configuration.  Clearance required for movement equals reach of arm.*

• End of arm fixturing allows operator the full grip of tool with no pinch points

• Power source for arm is mechanical (no air line is required)

• Shipped with two TW-3 balancers

• Use with inline higher torque DC nutrunner

• Use with pistol grip lower torque DC nutrunner (requires addition of part 0045 or 0047)

• Vertical or horizontal screw application

• Side by side configuration of linear slides provide additional stability for heavier or higher torque tools

• Arm movement is up-down and 360^o side-side rotation unless limited by tool configuration.  Clearance required for movement equals reach of arm.*

• End of arm fixturing allows operator the full grip of tool with no pinch points

• Optional swivel tool mount is available

• Power source for arm is mechanical (no air line is required)

• Shipped with two TW-3 balancers